×

INDI Library v2.0.6 is Released (02 Feb 2024)

Bi-monthly release with minor bug fixes and improvements

iOptron PEC update to drivers

  • Posts: 32
  • Thank you received: 5
Hello,

I have updated the iEQ driver and iOptron V3 to support PEC Start / Stop and PEC train cancel.

The V3 driver also supports checking the data status on the chip.

The iEQ driver supports a timer, which is set in the header file.

We are currently testing the code in github.com/seventi71/indi

Current Snag List:
1.) Need to limit PEC to mounts that support it, on both drivers. - not done yet.
2.) Parking gets stuck in a loop, until tracking is manually turned off and on.
- known bug in firmware, already logged with ioptron. best work around is to start from a parked position, then avoid problem.
3.) Slew rate jumps to next fastest when you set it.
Simon, found this and raised ticket on Indi master thread in github.
4.) Set capability is on 9 instead of 10.
- tested this, 9 slew rates is correct. This is not a bug.

Edit: will update this post as we work through these. 
 
Christopher | Sussex England | n2042.blogspot.com
iOptron GEM45 | Altair Mobile Pier | TSPhoton 154 @ F3.7
ASI 294MM Pro | ASI EFW | ASI EAF | ASI 120MM
Mini PC | Quad 4GB 64GB 5G | Juice USB Harness
The following user(s) said Thank You: Gonzothegreat, Eivind
Last edit: 2 years 11 months ago by christopher. Reason: Snag list updates.
3 years 2 months ago #66345

Please Log in or Create an account to join the conversation.

  • Posts: 32
  • Thank you received: 5
Anybody who is interested in this, I now have a working modified driver for iEQ, which supports SetPEC On, SetPEC Off, TrainPEC and Cancel with a timer that can be set for training.
Later this could be set to worm drive period per mount, if we can get the timings. mine is 400 seconds.

I cannot get the GPR (get recording status) or GPE (get data quality) serial commands to work, I just get a read error.
(Edit - Update firmware and switch to iOptron v3 drivers and GPE works)


My current thinking is to guide using EKOS or PHD2 using the PPEC algorithm for 5 cycles, to build up a good smooth curve and then to record it.
Then once recorded, reset the guiding to get it to learn off the new improved cycle.

Does anybody want to test this, I will be running my first tests on Thursday evening if the stars stay out.

Regards
Chris
Christopher | Sussex England | n2042.blogspot.com
iOptron GEM45 | Altair Mobile Pier | TSPhoton 154 @ F3.7
ASI 294MM Pro | ASI EFW | ASI EAF | ASI 120MM
Mini PC | Quad 4GB 64GB 5G | Juice USB Harness
Last edit: 3 years 1 month ago by christopher.
3 years 1 month ago #67116

Please Log in or Create an account to join the conversation.

  • Posts: 32
  • Thank you received: 5
Hello,

Cool, super impressed i have managed to get PEC code to work inside iOptron V3 driver.



Current Capabilities:
- PEC On / Off
- Train On/Off
- Data status

I have created a fork seventi71/indi
Anybody want to do some testing on this?

My thoughts for testing which i will be doing next week are as follows:
Get precise polar alignment
Then guide using the GPA algorithm for 5 full cycles. 400s x 5
Then configure GPA to 100% Predictive and 0% reactive.
This way it will only be issuing predictive commands.
Then i will record PEC.

Will update on here on how it works.

Regards
Chris
Christopher | Sussex England | n2042.blogspot.com
iOptron GEM45 | Altair Mobile Pier | TSPhoton 154 @ F3.7
ASI 294MM Pro | ASI EFW | ASI EAF | ASI 120MM
Mini PC | Quad 4GB 64GB 5G | Juice USB Harness
Last edit: 3 years 1 month ago by christopher.
3 years 1 month ago #67588

Please Log in or Create an account to join the conversation.

  • Posts: 245
  • Thank you received: 56
Very curious to see your first results.
Is it advisable to use PEC and guiding together or will they get in each others way?
3 years 1 month ago #67640

Please Log in or Create an account to join the conversation.

  • Posts: 32
  • Thank you received: 5
Theory around this from cloudy nights / stargazer's lounge forum and what i have done some research on.
Happy to be corrected on these, please jump in!

A note about the mount and guiding:
The GEM45 has 216 teeth and a cycle of 400 seconds, with a tooth to tooth period of 1.85 seconds.
My thoughts are an exposure times of up to 1.85 seconds, which will allow at least a pulse per tooth.
Seeing conditions will dictate the exposure times as well, to avoid chasing seeing.
(Although some debate about this, so best to experiment.)

Types of Errors:
1.) PEC -> Error in the alignment of the drive (on RA only.)
This creates some positive and then some negative guide pulses on regular schedule based on drive cycle.
GEM 45 / CEM 40 is 400s on RA, which can be eliminated through predictive pulses stored on a chip on the drive.
(These are the pulses we want to eliminate, when we are recording.)

2.) Polar / Level misalignment will create pulses in a single direction, on both RA and DEC.
This creates some positive OR negative pulses in a single direction, based on the amount of misalignment.
(If you have a permanent setup, it can be wise to slightly polar misalign on RA, to reduce backlash, then these + PEC can be recorded onto the chip.
If like me your setup is mobile, then it is best to avoid this while recording for good clean recording.
Drift aligning on on RA near the meridian will get this close to perfect.)

3.) Balance / Backlash, this may create pulses after a pulse to correct overstatement.
When a mount counterweight is light, the unbalanced is in the opposite sidereal direction of RA, which means that it is putting positive pressure on the worm gear that is lifting the scope.
However after a meridian flip, it will be lying on the leading edge on the tooth, which puts a negative pressure on the worm gear as it is lowing the scope.
Backlash is when the weight of the mount needs to move from a one side of the tooth to the other, to get it to move the mount.
(These types of pulses cannot be corrected, with PEC and should be corrected by balancing mount correctly.)
(Guiding will still help with this)

4.) Wind, vibrations, other random noise / jitter, etc
These pulses are random noise and can only be corrected with a guide star.

5.) Seeing conditions should be eliminated by setting your guiding exposure times, as high as possible for your mount.

Recording Assumptions:
Based on the above assumptions, the following procedure will be performed as part of the recording procedure.
1.) Setup mount on a solid concrete patio, to avoid vibrations.
2.) Get mount as level as possible, and polar align with iPolar.
3.) Slew to a near equator (opposite of polaris) and on the right of the meridian. (I am in the Northern Hemisphere.)
It means that my mount will be lifting the scope on each tooth with a lite counterweight, to reduce any backlash.
4.) Guide on 1.85s exposure and drift align near meridian to make sure that my RA is really good.
This should ensure that i can get a great RA drift alignment but with very little DEC interference.
5.) Turn on GPA guiding and guide for 4 worm cycles to train GPA predictive on PEC, (400s *4)
6.) Adjust the GPA prediction gain to 100% and control gain to 0% and commence recording.

Remarks
I will post the before guide graph and the after guide graphs on here.
The idea here is to make sure that i only get the predictive pulses, recorded into the CHIP.
This way in the future PEC is eliminated immediately, and GPA can focus on polar drift / level / balance issues.
Christopher | Sussex England | n2042.blogspot.com
iOptron GEM45 | Altair Mobile Pier | TSPhoton 154 @ F3.7
ASI 294MM Pro | ASI EFW | ASI EAF | ASI 120MM
Mini PC | Quad 4GB 64GB 5G | Juice USB Harness
Last edit: 3 years 1 month ago by christopher.
3 years 1 month ago #67642

Please Log in or Create an account to join the conversation.

  • Posts: 44
  • Thank you received: 5
Great work! Unfortunately I had no available time to test it. Did you make any progress with predictive guiding recording?

Also, I noticed into you that you set back baudrate to 115200, since the v3 driver default to 9600. Was it necessary for proper connection? If so, we have to advice Jasem that defaulting to v3 driver in indi 1.8.9 broke GEM45 communication.
3 years 3 weeks ago #68047

Please Log in or Create an account to join the conversation.

  • Posts: 32
  • Thank you received: 5
Okay super frustrated, since i updated my firmware and moved to the V3 driver, my mount is doing something super weird.
I cannot slew to a target in Kstars, because it keeps slewing in the opposite direction.
I thought it was because of something i broke in the code. So i have done a purge and reinstall from scratch on the stable drivers - same issue. I formatted the machine and reinstalled everything from scratch and it still does it. why?

I found this thread of others that have the same issue.
www.indilib.org/forum/general/8852-locat....html?start=24#68128
Edit: Spent this afternoon working out the issue, see above thread for solution.

Now i have to wait some days for the stars to appear again.
Also updated my fork to include the correct buadrate and to be able to findhome for GEM45.
Christopher | Sussex England | n2042.blogspot.com
iOptron GEM45 | Altair Mobile Pier | TSPhoton 154 @ F3.7
ASI 294MM Pro | ASI EFW | ASI EAF | ASI 120MM
Mini PC | Quad 4GB 64GB 5G | Juice USB Harness
Last edit: 3 years 3 weeks ago by christopher.
3 years 3 weeks ago #68130

Please Log in or Create an account to join the conversation.

  • Posts: 2247
  • Thank you received: 223
Nice work on including PEC.
The CEM25p has PEC capabilities, I'm going to have a peek at what you've done and see if it can added to the ieq driver.
3 years 2 weeks ago #68521

Please Log in or Create an account to join the conversation.

  • Posts: 32
  • Thank you received: 5
Hey Gonzo,

i originally wrote the code in iEQ driver. the issue i had was with the check data status.
the cem25 firmware will not support the capability to report data status.

I have reverted the code back into the iEQ driver in my fork.
github/seventi71/indi
Happy for you to add improvements :)

If you are on the latest firmware and the report data status does not work, you will get errors, let me know.

Over the weekend i can update the getDataStatus function to use a timer, instead of a checking completion.
The Gem28 has a worm period of 600secs, as this is the longest period, i will set it in the header file.
If your mount is say 500sec, it will automatically stop recording in the mount, even though the driver will still say recording until timer ends.
We could put a table in the header with the timings of the different mounts, not sure if worth it vs a fixed amount.
All the new mounts will work on v3 firmware, so should be able to use the new driver.

Regards
Chris
Christopher | Sussex England | n2042.blogspot.com
iOptron GEM45 | Altair Mobile Pier | TSPhoton 154 @ F3.7
ASI 294MM Pro | ASI EFW | ASI EAF | ASI 120MM
Mini PC | Quad 4GB 64GB 5G | Juice USB Harness
Last edit: 3 years 2 weeks ago by christopher.
3 years 2 weeks ago #68543

Please Log in or Create an account to join the conversation.

  • Posts: 2247
  • Thank you received: 223
thanks, I will git clone your repo and test your driver on my CEM25p which has the latest firmware (I believe).
The following user(s) said Thank You: christopher
3 years 2 weeks ago #68547

Please Log in or Create an account to join the conversation.

  • Posts: 2247
  • Thank you received: 223
Testing it...

First thing I noticed is that the park function is broken, you can issue a park and the mount will slew to the park position but never actually finish.
2021-03-12T10:12:43: [INFO] Parking is in progress...
2021-03-12T10:12:43: [INFO] Slewing to RA: 22:05:37 - DEC: 90:00:00

While on the normal driver:
2021-03-12T10:10:21: [INFO] Mount is parked.
2021-03-12T10:10:20: [INFO] Manual parking complete. Shut the mount down.
2021-03-12T10:10:06: [INFO] Parking is in progress...

and the second thing is I see the following error:
2021-03-12T10:12:27: [ERROR] Serial read error: Timeout error.

and I cannot test the PEC right now as it needs guiding, but I think I can test that with the sims later on today
3 years 2 weeks ago #68548

Please Log in or Create an account to join the conversation.

  • Posts: 245
  • Thank you received: 56
I don't know if it helps but I had the same parking issue on my GEM45. I reset the park position using the hand controller (goto home, set park to current) and after that the park in Indi worked again as expected (it completed).
3 years 2 weeks ago #68552

Please Log in or Create an account to join the conversation.

Time to create page: 0.669 seconds