×

INDI Library v1.9.6 Released (21 May 2022)

Bi-monthly INDI Library released with new drivers and bug fixes.

Read More...

[SOLVED] parameter not saved

  • Posts: 806
  • Thank you received: 126

parameter not saved was created by Alfred

In the CCD tab the parameter "guiding deviation" always comes up at "0.50" (Build: 2019-08-26T15:10:15Z). I have to change that to 2.0 time and time again. Also the ticks at "duration" and "TS" disappear on every startup. Shouldn't these settings be saved and auto restored on the next launch?
2 years 10 months ago #42583

Please Log in or Create an account to join the conversation.

  • Posts: 1941
  • Thank you received: 416

Replied by Wouter van Reeven on topic parameter not saved

The "duration" and "TS" (and in my case "filter" as well) are unticked for me every time as well. I agree that it would be great if they can be persisted over different sessions.
Wouter van Reeven

ASI6200MM and 7 slot 2" filter wheel with a SkyWatcher Esprit 80 ED on a SkyWatcher HEQ5-Pro
ASI1600MM-Pro Cooled and 5 slot 1.25" filter wheel with an 8" TS Ritchey-Chrétien on a SkyWatcher EQ6-R
The following user(s) said Thank You: Alfred
2 years 10 months ago #42585

Please Log in or Create an account to join the conversation.

  • Posts: 806
  • Thank you received: 126

Replied by Alfred on topic parameter not saved

Maybe we could make these boxes ticked the default setting?
2 years 10 months ago #42655

Please Log in or Create an account to join the conversation.

  • Posts: 938
  • Thank you received: 285

Replied by Wolfgang Reissenberger on topic parameter not saved

Same problem, different explanations:
  1. guiding deviation: that's a bug, the value is stored, but it is initialized with the autofocus HFR value (copy paste error).
  2. check marks for filter, duration and time stamp: they are not stored currently.
As a work around: store the entire capture session and reload it from file. Then all parameters are set appropriately.

- Wolfgang
TSA-120 + epsilon-160 + FSQ-85 + GSO 150/750 | Avalon Linear + M-zero | ASI 1600mm pro + 6200mm pro | KStars/INDI on Raspberry Pi 4/Intel NUC
The following user(s) said Thank You: Alfred, Wouter van Reeven
2 years 10 months ago #42674

Please Log in or Create an account to join the conversation.

  • Posts: 1941
  • Thank you received: 416

Replied by Wouter van Reeven on topic parameter not saved

Thanks for the suggestion Wolfgang. I can verify that this works since I have done this before. I’ll do that until the state of the check boxes is persisted.


Clear skies, Wouter
Wouter van Reeven

ASI6200MM and 7 slot 2" filter wheel with a SkyWatcher Esprit 80 ED on a SkyWatcher HEQ5-Pro
ASI1600MM-Pro Cooled and 5 slot 1.25" filter wheel with an 8" TS Ritchey-Chrétien on a SkyWatcher EQ6-R
2 years 10 months ago #42679

Please Log in or Create an account to join the conversation.

  • Posts: 938
  • Thank you received: 285

Replied by Wolfgang Reissenberger on topic parameter not saved

OK folks, issue is solved. If you are willing to compile from sources, you can obtain it already.

- Wolfgang
TSA-120 + epsilon-160 + FSQ-85 + GSO 150/750 | Avalon Linear + M-zero | ASI 1600mm pro + 6200mm pro | KStars/INDI on Raspberry Pi 4/Intel NUC
The following user(s) said Thank You: Alfred
2 years 10 months ago #42712

Please Log in or Create an account to join the conversation.

  • Posts: 1941
  • Thank you received: 416

Replied by Wouter van Reeven on topic parameter not saved

Thanks very much! Currently I am in the South of France and we are swamped with thunderstorms so I’ll wait for this to become available in the nightly builds.


Wouter
Wouter van Reeven

ASI6200MM and 7 slot 2" filter wheel with a SkyWatcher Esprit 80 ED on a SkyWatcher HEQ5-Pro
ASI1600MM-Pro Cooled and 5 slot 1.25" filter wheel with an 8" TS Ritchey-Chrétien on a SkyWatcher EQ6-R
2 years 10 months ago #42714

Please Log in or Create an account to join the conversation.

  • Posts: 806
  • Thank you received: 126

Replied by Alfred on topic [SOLVED] parameter not saved

Git pulled, tested, LIKED! Works like a charm, thanks an awful lot, Wolfgang!
Last edit: 2 years 10 months ago by Alfred.
2 years 10 months ago #42729

Please Log in or Create an account to join the conversation.

Time to create page: 0.239 seconds