×

INDI Library v2.0.6 is Released (02 Feb 2024)

Bi-monthly release with minor bug fixes and improvements

Ioptron mount connection support needed

  • Posts: 1009
  • Thank you received: 133
The CEM120 needs a different driver (talking Protocol 3.0) than the smaller ones (Protocol 2.5).
So you'd need the indi_ioptronv3_telescope driver. While command sets are quite similar and you likely can connect, especially the get position one is different, which will make operation fail.
The following user(s) said Thank You: Craig, Theodore Wyshyvanuk
4 years 5 months ago #44075

Please Log in or Create an account to join the conversation.

  • Posts: 28
  • Thank you received: 0
Alas, unlike the original poster, I have an iOptron IEQ45 GTN, the model just prior to the Pro. It has the RS232 port rather than the USB. I'm using an RS232/USB convertor with what I believe is a Prolific chip. Sorry for causing confusion!!
4 years 5 months ago #44078

Please Log in or Create an account to join the conversation.

  • Posts: 1009
  • Thank you received: 133
Not sure which INDI version you have, if it is a newer one, you might try the old driver, indi_ieqlegacy_telescope.
4 years 5 months ago #44080

Please Log in or Create an account to join the conversation.

  • Posts: 28
  • Thank you received: 0
More info:
1. I've tried choosing all of the available iOptron mounts that looked al all promising, to include iOptron iEQ Legacy, but all result in a Failed to Connect error (2019-09-30T15:48:25: [ERROR] Failed to connect to port (/dev/cu.usbserial). Error: Port failure Error: No such file or directory. Check if device is connected to this port." . Last night, unless I was delirious, I found one that resulted in a Timeout error. I haven't been able to duplicate that this morning.
2. It looks like some of the mount choices result in using the same driver. I'm assuming that this is as it should be.
3. Ports shows /dev.cu.usbserial in both slots, but System Ports shows /dev/cu.Bluetooth-Incoming-Port. If the System Ports slot is clicked/selected, the Ports slot changes to /dev/cu.Bluetooth-Incoming-Port, to match.

I'm totally available to try anything that might clear this issue. Thanks for any advice or insight!!!

I'm at your service
4 years 5 months ago #44083

Please Log in or Create an account to join the conversation.

  • Posts: 456
  • Thank you received: 76
Here's a screenshot from my setup. CEM120, plugged into the mount base USB.
One thing to check is the baud rate? Set to 115200
If you need more screenshots let me know. If you are still stuck.... maybe some one of us can teamviewer into your setup?
4 years 5 months ago #44086
Attachments:

Please Log in or Create an account to join the conversation.

  • Posts: 1009
  • Thank you received: 133
Uhm, maybe some splitoff is needed here. The original post from almost half a year ago was about the CEM120, but the current issue of wyshyvanuk is with another model, the IEQ45 GTN. So CEM120 settings do not help :(

@wyshyvanuk: What hand controller do you have? 8406 or 8407? If the former, you should use the HC8406 driver, indi_ioptronHC8406 if the listing on the driver page is correct,.
I seem to remember some note that some driver needs the mount to be star-aligned with the HC before you can use it with INDI - maybe it was this one? Have you tried that, doing a 1/3 star alignment before connecting?
4 years 5 months ago #44089

Please Log in or Create an account to join the conversation.

  • Posts: 28
  • Thank you received: 0
I have the 8407. The indication on the driver page is that the INDI ZEQ25 should apply. Choosing this on the Profile Editor results in the correct Name and Exec in the Control Panel. But the mount still fails to connect. The rig is set up in my study. I haven't had the courage to actually take it outdoors yet ;~). Thanks!!!
4 years 5 months ago #44091

Please Log in or Create an account to join the conversation.

  • Posts: 1009
  • Thank you received: 133
Well, testing things indoors first is always the better choice :)
Just for confirmation - you are using some Stellarmate or similar? Because the port name does look very unfamiliar. Unfortunately I've never used one of those, so I don't know exactly how to handle them.
Does the INDI control panel have the 'Auto Search' enabled (in the Connection tab)? If not maybe have a try with that.
4 years 5 months ago #44093

Please Log in or Create an account to join the conversation.

  • Posts: 456
  • Thank you received: 76
soooory, my bad. I didn't realise this thread was that old I thought it was a new thread relating to CEM120 connection problems. Please ignore my message above. Sorry for confusion
4 years 5 months ago #44094

Please Log in or Create an account to join the conversation.

  • Posts: 28
  • Thank you received: 0
Stellarmate in not being used. I have the elements on the tripod connected directly to my Mac using USB connections and an RS232/USB adaptor. I've flipped back and forth between Auto Search Enabled and Disabled, but it's mostly been on Enabled.
Regards,
Ted
4 years 5 months ago #44095

Please Log in or Create an account to join the conversation.

  • Posts: 28
  • Thank you received: 0
The CEM120 (yes, I do want one) issue was my fault entirely. I was led into this post by the RS232 /USB issue.
Ted
4 years 5 months ago #44096

Please Log in or Create an account to join the conversation.

  • Posts: 28
  • Thank you received: 0
Progress: I've learned, at long last, that a driver must be installed for the RS232 to USB adaptor. My apologies for dragging you through this quagmire.
1. My adaptor apparently uses a Prolific chip. I downloaded and installed the appropriate driver from Prolific, and, oh my, EKOS recognizes the IEQ45 mount using the ZEQ25 profile.
2. However, the mount is not responding to any "movement" controls from the Mac. The mount WILL move when linked to the 8407 HC.
3. The iOptron website suggests using the FTDI chip on the adaptor. I have ordered an adaptor with that chip. I'm not optimistic, but what the heck.
As always, any insight or advice is welcomed!! Moving the mount would seem to be an integral part of the installation ;~).
4 years 5 months ago #44129

Please Log in or Create an account to join the conversation.

Time to create page: 2.759 seconds