Come and join our community. Expand your network and get to know new people!
Hi Steve, had a look at the logs, they look mostly normal to me, and if the ttyUSB1 stays that way I wouldn't bother too much, got some questions:
- do you have a so called eqmod cable? it seems pl2303 may look like one and the eqmod chip may cause problems on Linux (I recomment in fact using normal USB cables)
- are you running through a powered USB? The lines containing "over-current change" indicate that whatever device is there is requesting more current than the pi may provide. Can't tell for sure what kind of device is there, you may have more luck adding usb_max_current_enable=1 in /boot/config.txt
Read More...
On both my Intel NUC 11 Essential and my BeeLink U59 I had numerous display issues (and even becoming non-responsive) with StellarMate X OS.
Once I disabled the Compositor under the Display and Monitor in System Settings I have no longer seen this issue.
I don't think this is enabled on the RPi version of StellarMate (haven't used it in a few months).
Read More...
Thanks, Mattia.
This issue has come back to rear its ugly head again.
I had gotten disgusted with my GPS dongle and have removed it from the system. Only to find that /dev/ttyUSB0 still disappears from the /dev/ directory listing only to find /dev/ttyUSB1 appearing in its place, even without the dongle.
I am attaching a file containing dmesg output. Perhaps it will suggest something,
I would call your attention to lines 567-580, Maybe you can help me understand what they mean.
[Thu Apr 25 21:02:33 2024] pl2303 ttyUSB0: usb_serial_generic_write_bulk_callback - nonzero urb status: -71
[Thu Apr 25 21:02:33 2024] usb 3-2: USB disconnect, device number 2
[Thu Apr 25 21:02:33 2024] usb 1-2: USB disconnect, device number 3
[Thu Apr 25 21:02:33 2024] pl2303 ttyUSB0: pl2303_read_int_callback - usb_submit_urb failed with result -19
[Thu Apr 25 21:02:33 2024] pl2303 ttyUSB0: error sending break = -19
[Thu Apr 25 21:02:33 2024] pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
[Thu Apr 25 21:02:33 2024] pl2303 1-2:1.0: device disconnected
[Thu Apr 25 21:02:33 2024] usb 1-2: new full-speed USB device number 5 using xhci-hcd
[Thu Apr 25 21:02:34 2024] usb 1-2: New USB device found, idVendor=067b, idProduct=2303, bcdDevice= 4.00
[Thu Apr 25 21:02:34 2024] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[Thu Apr 25 21:02:34 2024] usb 1-2: Product: USB-Serial Controller D
[Thu Apr 25 21:02:34 2024] usb 1-2: Manufacturer: Prolific Technology Inc.
[Thu Apr 25 21:02:34 2024] pl2303 1-2:1.0: pl2303 converter detected
[Thu Apr 25 21:02:34 2024] usb 1-2: pl2303 converter now attached to ttyUSB1
After getting a new Raspberry Pi5 (running Astroarch), working through and solving flaky WiFi issues, flaky cable issues, I now find myself finally able to use KStars and Ekos again.
But I am immediately met with errors on my ZWO ASI533MC PRO and ZWO EAF devices. I don't know how to solve any of them.
The devices connect in EKos, but quickly develop errors that prevent anything useful from being done. I am enclosing some INDI driver logs in the hope that someone can help me understand them. Besides the question of the specific errors in the logs, I am thinking there may be a more global problem with my Pi5. Why should all these devices be failing at the same time?
Hello,
From yesterday to today, the Control mount icon has moved from Ekos to Sky screen.
I can't figure out the interest of this - I would rather consider this a problem, as it is not possible anymore to monitor the target while trying to center it.
Where it was until yesterday :
Agreed I seem to have a more general problem. When I went to get things set up after dark using the 'new' profile the limit issue had returned along with others that ended the session.
Read More...
As best I can tell, the limits are not stored with the profile. When I make a change, it appears in all profiles. It does seem like it should be per profile, but I guess not.
Read More...
I can see how that would be annoying. I would make it easier to find support requests, I just do not know if there is enough interest in this specific topic to support a new category.
Read More...
Thanks Bill,
Made me define a new profile with the same devices. The same unwanted values showed up but now changes are retained. Don't know what it means but guess I'll go ahead and customize that profile instead of my usual one.
/Tom
Read More...
Looks like that fixed it. Thanks, Jasem!!!!
Read More...
Jean-Luc, it sounds like you've got this sorted but I've attached screenshots of my set up for opticat trains and guiding just FYI. I think this is the similar to what Bill was describing.
Good luck!
Fred
FWIW: I'm not seeing that problem on the Mac version of KStars/Ekos. I've changed the values several times and it is always remembered next time I start up.
Read More...
That's fine, I wonder why I had set it to Mount once, probably a misclick while trying to adjust something else.
Thank-you for helping.
Read More...