Reiner vom Bruch replied to the topic 'CCD Autostart Cooling' in the forum. 2 months ago

Should we create a feature request?

Read More...

Reiner vom Bruch replied to the topic 'CCD Autostart Cooling' in the forum. 2 months ago

No this is not stored.

I think I remember there was a Point in Kstars to select automatic start of cooling. Just as autostart tracking
But I can´t find it. Too bad

Read More...

Reiner vom Bruch replied to the topic 'CCD Autostart Cooling' in the forum. 2 months ago

By the way, I´m using Astroberry. But that shouldn´t make a difference.

Read More...

Reiner vom Bruch replied to the topic 'CCD Autostart Cooling' in the forum. 2 months ago

Hi Wouter,

sorry, I don´t find it

I think you mean the Main-Control-Panel for My Camera ?
There I find the Setpoint for Cooling. But this is not stored.
It´s an Starlihjt Xpress Trius 694

CS
Reiner

Read More...

Reiner vom Bruch created a new topic ' CCD Autostart Cooling' in the forum. 2 months ago

Hi All,

is there any chance to autostart the CCD Cooling ? Perhaps as a Point in the Sequence?
When you start the sequence, the selected Temperatur will be selected and activated.

Last night I adjusted the Temperature but forgot to start it

CS
Reiner

Read More...

Reiner vom Bruch replied to the topic 'Using BerryBoot to run Astroberry from an SSD' in the forum. 2 months ago

Hi !

I used this tutorial (in German) to transfer everything from SD to SSD for thee RPI4. And everything is working fine. I did this with a ready installed astroberry on SD-Card and transferred this to the SSD.

Why using the SSD ?
After I´ve lost a view SD-Cards because of Power-loss (exidently and stupidly ;-) ) I didn´t feel like it anymore. So I bought 3 Kingston industrial SD, installed Astroberry and then I did the steps explained in the Video. Since the I´ve never had that issue again. And its faster...

CS
Reiner

Read More...

Reiner vom Bruch replied to the topic 'Astroberry and Onstep Mini2 (Teensy 3.2)' in the forum. 2 months ago

Thanks a lot.

now anothe issue,

I´m not able to adjust the slew rate via indi control panel and also not with kstars Mount control.
In indi-control panel I can see "Setting Max Slew Rate to (1...9)", but this is not adjusted in Onstep himself.
The only thing that works is, when I use the Onstep App and adjust the speed at Guide/Focus there.

My Setup:
RPI4 with Astroberry and SSD, the Onstep MiniPCB2 (Teensy 3.2)
SX-CCD and the UPB Powerbox.
KStars for Windows 3.4.1 on my Win 10 Laptop
Both connected via GBit Lan
No error-messages at all.

Any idear ?

CS
Reiner

Read More...

Reiner vom Bruch replied to the topic 'Astroberry and Onstep Mini2 (Teensy 3.2)' in the forum. 2 months ago

Hej G_!

your tip did it:
sudo apt-get remove modemmanager

Thanks
Reiner

Read More...

Reiner vom Bruch replied to the topic 'Astroberry and Onstep Mini2 (Teensy 3.2)' in the forum. 2 months ago

Hi Radek,

I´ve selected the LX200 Onstep Driver

@G_
I give it a try and will report what happend

CS
Reiner

Read More...

Reiner vom Bruch replied to the topic 'Cannot Connect to Astroberry VAP' in the forum. 2 months ago

Hi All,

I have the same issue with my Galaxy S9 +
My Iphone, iPad Air, Sony Xperia X3 and my Oneplus connect without any Problem. It seams to be related to Samsung.

CS
Reiner

Read More...

Reiner vom Bruch replied to the topic 'Boxdoerfer Dynostar Mount Control' in the forum. 2 months ago

Hi Joshi,

if you use the FS Driver, the hand control is functioning

CS
Reiner

Read More...

Reiner vom Bruch created a new topic ' Astroberry and Onstep Mini2 (Teensy 3.2)' in the forum. 2 months ago

Hello All,

I´m triying to connct my new Onstep Mini2. The contoller and USB is the Teensy 3.2.
It comes at indi as /dev/ttyACM0. I Select that but the connection will not be established.
At the console : cat /dev/ttyACM0 is also hanging. No response.

What can I do ?

By the way, Onstep and Ascom is working at my Win 10 PC

CS Reiner

Read More...

Reiner vom Bruch replied to the topic 'Boxdoerfer Dynostar Mount Control' in the forum. 3 months ago

Hi Wildi,

just got the time, to test the LX 200 classic Driver. See the attached image.

With the Basic I don´t get this messages. How ever, the Dynostar may not be able to access the commands.

With the basic driver it works exept the the Software Handbox, as Joshi wrote.

CS
Reiner

Read More...